Why corrosion protection is essential
Steel is thermodynamically unstable in soil, water and a humid atmosphere: it tends to return to its original, oxidised state – in other words, to rust (Fig. 1). Without protective measures, this electrochemical process leads to a reduction in wall thickness, pitting and, in the worst case, component failure (Fig. 2). In the case of pipelines for gas, hydrogen or other media where the media are transported under pressure, this is not merely a question of cost-effectiveness, but is directly relevant to safety. Furthermore, underground pipelines cannot be inspected visually. Corrosion protection must therefore be taken into account right from the planning stage of these pipeline systems.
Unlike many other forms of damage, corrosion is a gradual process and often only comes to public attention following spectacular incidents such as burst pipes, pipeline leaks or the collapse of structures. For operators of pipeline networks, this means that corrosion management is not a one-off construction project, but an ongoing operational task throughout the entire life cycle of a facility – from the selection of materials and coatings, through commissioning, to ongoing monitoring and maintenance.
Economic significance
The economic scale of the corrosion problem is regularly underestimated because the costs are widely dispersed and can rarely be attributed to a single incident. The most widely cited international study, the IMPACT study by NACE International (now AMPP) from 2016, puts the global cost of corrosion at around 2.5 trillion US dollars per year – this corresponds to around 3.4 per cent of global economic output. The study also estimates that the consistent application of established corrosion protection methods could save between 15 and 35 per cent of these costs – amounting to several hundred billion US dollars annually worldwide.
Similar figures are reported for industrialised countries: studies by the World Corrosion Organisation and further research estimate direct corrosion costs at around three to four per cent of gross domestic product; when indirect costs such as production losses are taken into account, the figure is in some cases significantly higher. For Germany, this would result in – depending on the range used as a basis – annual losses in the low to mid double-digit billions, and in some estimates even significantly higher. These figures cover all sectors of the economy, not just pipelines; however, they represent the This clearly illustrates the scale of investment required for corrosion protection in pipeline infrastructure.
A look at Germany’s pipeline infrastructure reveals the scale of assets that need to be protected here: the German gas network alone comprises around 40,000 kilometres of long-distance pipelines. Added to this are water, district heating and industrial pipeline networks of a comparable scale. Every kilometre of inadequately protected steel pipeline poses a potential risk to safety and supply, as well as entailing maintenance and replacement costs that, over decades, are passed on to network charges and thus ultimately borne by the general public. Consistent corrosion protection significantly extends the service life of the infrastructure and is therefore one of the most cost-effective measures for ensuring its safety.
Types of corrosion in steel pipework
Not all corrosion occurs in the same way – distinguishing between the different mechanisms of damage is crucial for selecting the right protection strategy:
- Surface corrosion (uniform erosion): The material is eroded uniformly over a large area. It is relatively easy to predict and calculate, but in the absence of protection, it will eventually affect wall thickness.
- Pitting corrosion: Locally confined but deep erosion, often occurring at defects in the coating or on non-uniform substrates. Particularly treacherous because, despite minimal material loss, it can quickly lead to perforation.
- Stress corrosion cracking: The interaction of mechanical tensile stress and a corrosive medium, leading to cracking without significant loss of material – difficult to detect, but critical to safety.
- Contact or bimetallic corrosion: Occurs when metals of different nobility are connected in an electrically conductive manner; the less noble metal corrodes preferentially (galvanic cell).
- Microbial-induced corrosion (MIC): Micro-organisms in the soil or medium alter the local chemistry at the pipe surface and accelerate corrosion.
- Alternating current corrosion: Alternating voltages induced by nearby high-voltage power lines, railway power supply systems or other external current sources can promote corrosion at coating defects, even when cathodic protection is active, and require specific assessment and protection strategies.
In practice, these mechanisms often occur in combination, which is why corrosion protection systems for pipework are generally designed as multi-layer systems: a combination of passive protection through coatings and active, electrochemical protection through cathodic corrosion protection.
Active corrosion protection
Active corrosion protection directly intervenes in the electrochemical corrosion process, rather than merely shielding the material mechanically from its environment. The basic principle is to polarise the steel component to be protected electrically in such a way that it becomes the cathode of an electrochemical system – no metal dissolution takes place at the cathode. This cathodic polarisation can be achieved in two ways: either by using sacrificial anodes made of less noble metals (galvanic or sacrificial anode protection), which dissolve in place of the pipe, or by applying a direct current from the outside, known as external current protection. Both methods are grouped under the umbrella term ‘cathodic corrosion protection’ (CCP).
Active protection is particularly essential where a seamless passive coating cannot, in practice, be guaranteed: transport pipelines stretch for kilometres, are subjected to mechanical stress during construction and age over the course of decades. Coating defects are inevitable, arising, for example, from transport, installation, ground movements or mechanical impacts caused by third parties. Cathodic corrosion protection comes into play precisely at these points of failure: it protects the steel even where the coating fails, and is therefore an effective complement – not a substitute – for passive protection.
Cathodic Corrosion Protection (CCP)
Cathodic corrosion protection is mandatory for steel pipelines laid underground in Germany in accordance with the DVGW regulations and DIN EN ISO 15589-1 for onshore pipeline systems in the oil and gas industry, and is regulated in detail by these standards. In external current protection – the method predominantly used in transmission networks – a rectifier unit is used to apply a protective voltage between the pipeline and anodes embedded in the ground. In galvanic protection, sacrificial anodes made of magnesium, zinc or aluminium perform this function without an external power source – a method that is particularly suitable for shorter sections of pipeline, tanks or fittings.
The effectiveness of the protection is measured using the pipe-to-ground potential and compared with standardised protection criteria; in addition, test plates, data loggers or continuous remote monitoring systems are used to reliably detect fluctuations caused, for example, by stray currents, railway interference or alternating current ingress. Particular technical care is required when combining these systems with AC isolation units in areas affected by alternating current from high-voltage power lines or railway infrastructure: these systems specifically divert alternating currents without interrupting the direct current component required for the KKS. As environmental conditions – for example, due to new neighbouring infrastructure or changes in ground conditions – as it can change over the course of the system’s operational life, the KKS is not a system that is set up once and for all, but must be regularly measured, assessed and, where necessary, adjusted.